low pressure gas steam generator

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages

low pressure gas steam generator have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.

low pressure gas steam generator.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
low pressure gas steam generator low pressure gas steam generator low pressure gas steam generator

Steam Turbine Technology | GE Steam Pow

Innovative blading technology is apparent in the steam turbines we manufacture through: Modern, three-dimensional profile design that results in higher efficiency; High pressure (HP), intermediate pressure (IP), and low pressure (LP) front stage blades that are milled from a single forging for excellent mechanical integrity and higher reliability

lexie@zozen.com > Get A Quote >

High Quality Low Pressure Small Size Move Easy Electri

Home – Coal Biomass Boilers – High Quality Low Pressure Small Size Move Easy Electric Steam Generator For Fermentor. Quick inquiry: I need the quotation of , the fuel is , the pressure is The 4 ton capacity fire tube gas oil fired steam boiler use for food factory in Philippines. thermal efficiency is 92%.

lexie@zozen.com > Get A Quote >

Catalog of CHP Technologies, Section 4. Technolog

Section 4. Technology Characterization – Steam Turbines . 4.1 . Introduction . Steam turbines are one of the most versatile and oldest prime mover technologies still in general production used to drive a generator or mechanical machinery. The first steam turbine used …

lexie@zozen.com > Get A Quote >

S.1 Heat Recovery Steam Generators - energy.kth.

Modifying this certain cycle (same gas turbine as above) to a dual pressure HRSG, with high pressure steam (same pressure and temperature as above) and low pressure steam (constituting 20% of the total steam flow - the rest is high pressure steam), the stack temperature of the exhaust is 80°C.

lexie@zozen.com > Get A Quote >

Low and High Pressure Steam Boiler l SIMONEAU | Simone

Simoneau Low and High Pressure Steam Boilers. Whether you are looking for a low, standard or high pressure steam generation, our steam boilers will meet your energy requirements. Span of pressure ranges from 15 to 650 psig (and above on demand) producing up to 99,9% steam purity.

lexie@zozen.com > Get A Quote >

low pressure gas steam generator - degrensvoorbij.

Steam Generators - Low Pressure Boiler - Ultimate Washer. A steam generator is used as a source of heat for thawing and de-icing aggregates. This low pressure boiler also speeds up the curing process for pre-cast concrete, pipe, pre-stress, block operations, saturating the curing area with steam, uniformly heating the concrete and speeding up the normal process.

lexie@zozen.com > Get A Quote >

flue gas steam generator | Industrial steam boile

flue gas steam generator Flue gas desulfurization – IDC-Online. 2019-2-4 · Flue gas desulfurization Flue gas desulfurization is commonly known as FGD and is the technology used for removing sulfur dioxide (SO 2) from the exhaust combustion flue gases of power plants that burn coal oroil to produce steam for the turbines that drive their electricity generators.

lexie@zozen.com > Get A Quote >

Steam Generators, Low Pressure Boiler - Ultimate Wash

A steam generator is used as a source of heat for thawing and de-icing aggregates. This low pressure boiler also speeds up the curing process for pre-cast concrete, pipe, pre-stress, block operations, saturating the curing area with steam, uniformly heating the …

lexie@zozen.com > Get A Quote >

low-pressure evaporator - an overview | ScienceDirect Topi

Paul D. Gremaud, in Heat Recovery Steam Generator Technology, 2017. 16.3.1 Flow-accelerated corrosion. FAC occurs predominantly in the tubes, headers, and risers of low-pressure evaporators and in the tubes and headers of economizers and feedwater preheaters operating in the 200–500°F temperature range. It occurs in areas where the velocity of the water or water/steam mixture is high such

lexie@zozen.com > Get A Quote >

Latest Steam Turbine Technologies forThermal Power Plan

gas turbine, generator and steam turbine rotor are aligned in tandem. Compared to a multi-shaft system By locating the low-pressure steam inlet at the front of the casing and creating a fl ow of steam between inner and outer casings, the structure makes it less likely for a top/bottom tempera-

lexie@zozen.com > Get A Quote >

Thermal power station - Wikiped

A thermal power station is a power station in which heat energy is converted to electric power.In most of the places in the world the turbine is steam-driven.Water is heated, turns into steam and spins a steam turbine which drives an electrical generator.After it passes through the turbine, the steam is condensed in a condenser and recycled to where it was heated; this is known as a Rankine cycle.

lexie@zozen.com > Get A Quote >