oil thermal boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

oil thermal boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


oil thermal boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
oil thermal boiler oil thermal boiler oil thermal boiler

Oil Boilers - eComfo

eComfort is an online Oil Boiler superstore, specializing in Oil Fired Boilers, Home Oil Boilers and Home Oil Fired Boilers. Compare Oil Fired Boiler models, specs and prices. Consult with our experienced Oil Boiler experts. Oil Boilers for sale.

lexie@zozen.com > Get A Quote >

Thermal Fluid VERSUS Saturated Steam - TT BOILE

In thermal oil heaters a special oil - a so-called heat transfer fluid (HTF) are used instead of steam as heat carrier, and is operating at atmospheric pressure up to abt. 300°C. For comparing this to water and steam, it would require a steam pressure of 85 bar to obtain this temperature.

lexie@zozen.com > Get A Quote >

Why Hot Oil Heating Systems Are Better Than Steam fo

May 23, 2019 · The thermal heating fluid runs through the system in a loop and requires no chemical regulation. 4. Hot Oil Boilers Can Operate at Higher Temperatures. When it comes to efficient heating, operating temperature is very important. Since hot oil has a higher boiling point than water, hot oil heating systems can operate at higher temperatures.

lexie@zozen.com > Get A Quote >

EPCB Steam Boiler Hot Water Boiler Thermal Oil Boile

EPCB boiler is a specialized boiler enterprise which focuses on industrial boilers and small power plant boilers, such as steam boiler, hot water boiler, thermal oil boiler and so on with coal, biomass, oil or gas fuel.

lexie@zozen.com > Get A Quote >

Thermal Fluid Heating Systems | Sigma Therm

Thermal Oil. Thermal oil offers the user the capability of high-temperature operation (up to 600F with organic thermal oils and 800F with certain synthetics) at very low pressures. Due to the low operating pressure and properties of thermal oil, most heaters are built to ASME Section VIII, and a licensed boiler operator is not typically required.

lexie@zozen.com > Get A Quote >

China Thermal Oil Boiler Manufacturers - Best Pric

The thermal oil boiler is used to force the medium to carry out liquid phase circulation, and the heat energy is transferred to the heating equipment and then returned to the heating furnace. Heating, with high operating temperatures at low pressures, …

lexie@zozen.com > Get A Quote >

Thermal Oil Heater - for High Temperature Process Heati

T T BOILERS Thermal Oil Heaters (also called Thermal Oil Boilers, Thermal Fluid Boilers, Hot Oil Units or Diathermic Heaters) are developed and designed especially for demanding process heating operations where no compromise on quality are …

lexie@zozen.com > Get A Quote >

Thermal Oil Boiler | Thermal Oil Heater | Thermal Oi

Thermal Oil Boiler. Thermal fluid heaters use specially designed thermal fluids or heat transfer oils and glycols that operate with wood fired, gas, oil or electric heaters. Thermal fluid heating is a type of indirect heating in which the liquid heat transfer medium is …

lexie@zozen.com > Get A Quote >

Hot oil boilers,hot oil heaters,thermal oil boile

Established in 1992, Romiter Group Limited are committed to manufacturing and exporting complete enery saving heating equipment, including thermal oil boiler (Thermal fluid heat transfer product), thermal oil steam generator, cryogenic storage Dewar. As we know, both water and steam are used as heat carriers in process heating systems.

lexie@zozen.com > Get A Quote >

Oil-Fired Boilers and Furnaces | Department of Ener

Oil-Fired Boilers and Furnaces. Oil-fired furnaces and boilers are a popular choice in areas of the country with limited access to natural gas, such as the Northeast. Oil-fired furnaces and boilers present an opportunity to use renewable fuels to heat your home. A number of companies are now offering heating oil blended with biodiesel,

lexie@zozen.com > Get A Quote >

Thermal oil heaters for hot oil heating systems | Pirobl

Thermal oil heaters. Our hot oil boilers provide heat through liquid fuel (HFO, light oil) and/or gaseous (natural gas, propane, etc.). A thermal oil boiler is the main component in a thermal fluid heating system, where a liquid fuel is heated and circulated to provide energy to different energy users within a closed circuit.

lexie@zozen.com > Get A Quote >