working principle of autoclave

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

working principle of autoclave have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


working principle of autoclave.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
working principle of autoclave working principle of autoclave working principle of autoclave

Super Heated Water Spray Steriliser - Water Sterilise

The working principle of Neelam Industries’ Autoclaves is based on the automatic counter pressure by injection of compressed air into the chamber during the entire cycle to minimize the differential pressure across the containers generated by the exposure to heat.

lexie@zozen.com > Get A Quote >

Principle Of Autoclave Sterilization Wholesale, Principle

Related Searches for principle of autoclave sterilization: working principle of a generator principle of magnetic flow meter refrigerator principle of working working principle of a centrifuge principle of pressure transmitter principle of pressure measurement working principle of refrigerator principle of ultrasonic flow meter principle of

lexie@zozen.com > Get A Quote >

Steam Sterilization Principles - ispe.gr.

amount of air will always be present in the autoclave cham-ber, but must be minimized. Insufficient air removal, steril-izer chamber vacuum leaks and poor steam quality (excess non-condensable gases) are the most common causes of sterilization failures. 6. Drying Wrapped items must be dry before they can be aseptically removed from the sterilizer.

lexie@zozen.com > Get A Quote >

Microbiology Online: Autoclaving: Real Sterilizati

8/24/2009 · Autoclaving: Real Sterilization This principle is used to reduce cooking time in the home pressure cooker and to reduce sterilizing time in the autoclave. It is important to note that the sterilizing agent is the moist heat, not the pressure. Working of Autoclave:

lexie@zozen.com > Get A Quote >

Autoclaves, laboratory autoclaves and sterilizers - Mad

AUTOCLAVE – DEFINITION AND APPLICATION AREAS. Autoclave (Greek/Latin: self-sealing): A gas-tight, sealable pressure vessel, used for the thermal treatment of substances in the overpressure range. Autoclaves are used for sterilising, curing building materials, for vulcanising tires and belts and for pressing fiber composites.

lexie@zozen.com > Get A Quote >

What is the principle of Autoclave - ALLIntervi

What is the principle of Autoclave.. Answer / perry. main principle of autoclave is mosit sterlization steam under pressure & temperature is 121degrees centigrade 15 Lbs pressure.AT THIS TEMPERATURE IT WILL destroy the thermophillic bacterias also if we exceed the …

lexie@zozen.com > Get A Quote >

Principle and Working of Autoclave - pharmaguideline.c

Principle and Working of Autoclave Autoclave is widely used for sterilization in pharmaceutical and healthcare sector. It is heating of articles at high temperature that is achieved by pressurizing the vessel. This article defines the principle of sterilization by autoclave.

lexie@zozen.com > Get A Quote >

What is the working principle of steam ejector? - Quo

4/26/2017 · I worked on a project before where a medical waste facility “cooked” the medical waste in a pressure vessel called an autoclave. After the cooking process the pressure inside the autoclave was around 3 Bar. In order to get all the water vapor out

lexie@zozen.com > Get A Quote >

Autoclave (industrial) - Wikiped

An autoclave applies both heat and pressure to the workload placed inside of it. Typically, there are two classes of autoclave. Those pressurized with steam process workloads which can withstand exposure to water, while circulating heated gas provides greater flexibility and control of the heating atmosphere.. Processing by autoclave is far more costly than oven heating and is therefore

lexie@zozen.com > Get A Quote >

The working principle and application prospect of autocla

The working principle of the autoclave steam sterilizer is very simple. It consists of a tank, a pressure gauge, a can lid, an exhaust valve, a safety valve and a heating wire. The pressure gauge is mainly for indicating pressure, and the exhaust valve is for exhausting.

lexie@zozen.com > Get A Quote >

How does an Autoclave work? | Topic | Astell

How does an Autoclave work? ‘Autoclave’ is a term used mainly in laboratories whilst ‘Sterilizer’ is used more commonly for medical and pharmaceutical applications. What is an autoclave? An effective Autoclave or Sterilizer must contain dry saturated steam. In order to achieve this, air must be removed from both the load and the

lexie@zozen.com > Get A Quote >