flue gas waste heat power generation boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

flue gas waste heat power generation boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


flue gas waste heat power generation boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
flue gas waste heat power generation boiler flue gas waste heat power generation boiler flue gas waste heat power generation boiler

can the waste heat from the gas tubine fire the gas boil

waste heat from flue gas recovery boiler cost – Drum Boiler Natural gas is frequently combusted in gas turbines as well as boilers.The waste heat from a gas turbine, in the form of hot exhaust gas, can be used to raise steam, by passing this gas through a heat recovery …Basics of Steam Generation – KTH2003-10-30 · The Basics of Steam Generation – 6 expansion is the source of power

lexie@zozen.com > Get A Quote >

Waste Heat Boilers - Fuel Efficient Distributed Generati

Waste Exhaust Heat Boilers. Approximately 25% of the usable energy of the fuel gas is released in the exhaust of the gas engine. This can be captured for cogeneration in a combined heat and power plant. This heat exits the engine at ~450 o C as ‘high grade heat’, contrasting to ‘low-grade heat’ available from the generator cooling circuits. This high temperature and flow makes it well

lexie@zozen.com > Get A Quote >

Flue Gas Waste Heat Boiler - stong-boiler.c

Therefore, Sitong Boiler design a number of flue gas waste heat boiler, which can save energy and reduce cost. Application: The flue gas waste heat boiler can be used in power generation plant and supply heating for city, hotel, hospital, bath center, textile industry, wood processing, paper making and other industries Advantages: 1.

lexie@zozen.com > Get A Quote >

Power 101: Flue Gas Heat Recovery in Power Plants, Part

Every power engineer must have a firm grasp of the rudiments of how fuel is processed to produce electricity in a power generation facility. heat from flue gas. waste heat for boiler

lexie@zozen.com > Get A Quote >

Waste Heat Boilers - Rentech Boile

Not recommended for waste flue gas streams with a high dew point temperature . Fire Tube Process Gas Boilers. RENTECH has extensive experience in supplying these industrial boilers for use in hydrogen reformer and hydrogen production systems commonly found in oil and gas, refining, and petrochemical plants.

lexie@zozen.com > Get A Quote >

Alfa Laval - Waste heat recove

Alfa Laval Aalborg offers a series of highly efficient waste heat recovery boilers that extract heat from hot flue gases and generate steam or hot water. A boiler is easily added to your flue gas stream and recovers heat that would normally be released into the air through a chimney. There are many possibilities to profit from recovered heat.

lexie@zozen.com > Get A Quote >