pressure vessel dish head

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

pressure vessel dish head have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


pressure vessel dish head.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
pressure vessel dish head pressure vessel dish head pressure vessel dish head

Vessel Volume & Level Calculation - CheCa

Vessel Head Diameter (D) mm Straight Length (L) mm Inside Dish Depth (a) mm f, Dish Radius parameter k, Knuckle Radius parameter

lexie@zozen.com > Get A Quote >

Dished Head dish head for pressure vess

C&N is a professional dish head for pressure vessel manufacturer.We can produce high quality head types on vessels are Hemispherical (Hemi), Semi Elliptical (SE), Flanged and Dished (F&D) and Flat

lexie@zozen.com > Get A Quote >

Pressure Vessel Tank Hea

For high pressure projects, the advantage of a Hemisphere is that most ASME code calculations require less minimum thickness to hold high pressure than a 2:1 Elliptical head. Read More P - PRESCOR R - REALIZES

lexie@zozen.com > Get A Quote >

Calculate Surface Areas and Cross-sectional Areas i

UniSim Design – Calculate Surface Areas and Cross-sectional Areas in Vessels with Dished Heads 2 Table of Contents Table of Contents 2 Background

lexie@zozen.com > Get A Quote >

Australian Pressure Vessel Heads - World Class Dished

The dive took an hour to descend to the bottom at which point the vessel itself shrank as much as 7cm. This meant that APV Heads had to design the Pilot's Chamber to withstand the pressure. If anything happened, this not only

lexie@zozen.com > Get A Quote >

Dished & Vessel Heads - Dished Heads Manufacturer

Manufacturer of Dished & Vessel Heads - Dished Heads, Vessel Heads offered by Devchand Engineers Private Limited, Surat, Gujarat. Send Email Send SMS Search Home Profile Products We Offer Contact Us Home » »

lexie@zozen.com > Get A Quote >

Pressure Vessel Dimension Inspecti

Pressure Vessel Dimension Inspection - Tolerances for Formed Head: You may know that there is a specific rule for dimensional checking of formed heads, based the fact that the UG-81 inner surface shall not deviate outside of the

lexie@zozen.com > Get A Quote >

Industrial Autoclave - Pressure Vessel, Storage Tank,

Taian Strength Equipments Co, Ltd had been dedicated in supplying industrial autoclave, storage tank and dish head products and solutions to worldwide customer over 20 years. We have 80 talented research and development

lexie@zozen.com > Get A Quote >

Calculate the Volume of Torispherical Head or Dish 1

Calculate the Volume of Torispherical Head or Dish 10% : In this i am going to explain How to calculate the Volume of Torispherical Head or Dish 10% before going to the topic you should know what is Torispherical head or dish where

lexie@zozen.com > Get A Quote >

Custom Fabricator Offering Head Forming, Fabrication

Conrex Steel is a custom fabricator offering head forming services, fabrication services, and heat treating services. CE Macpherson Div: Call: 800.461.2001 [email protected] Conrex Steel: Call: 800.387.5820 [email protected] Home

lexie@zozen.com > Get A Quote >

Analysis of Dished Head and Skirt Joint of Pressure

In pressure vessel, dish is supported to skirt by weld. Which have applied by internal pressure load, self-weight, Analysis of Dished Head and Skirt Joint of Pressure Vessel using FEA Method (IJSTE/ Volume 2 / Issue 1 / 010)

lexie@zozen.com > Get A Quote >