steam boiler capacity design

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

steam boiler capacity design have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


steam boiler capacity design.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
steam boiler capacity design steam boiler capacity design steam boiler capacity design

Boiler Feed Pump Selection | HPAC Engineeri

Steam-boiler systems are available in a broad range of sizes. The following steps apply to pump selection for an industrial steam boiler with a horsepower range of 100 to 1,200 and a design pressure of 150 to 500 psig. With large applications, it is common to …

lexie@zozen.com > Get A Quote >

15 Basic Steps in Boiler Design - Meee Service

Boiler design is the process of designing boilers used for various purposes.The main function of a boiler is to heat water for steam generation. Steam produced can be used for a variety of purposes including space heating, sterilization, drying, humidification and power generation. The temperature or condition of steam required for these applications is different, so how to design a boiler

lexie@zozen.com > Get A Quote >

Boiler (power generation) - Wikiped

A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.

lexie@zozen.com > Get A Quote >

1 of 53 KLM Technology Group Rev: 01 - Kolmetz.c

Boiler capacity 40 Boiler Blow Down 41 Normally have large capacity, high steam parameters, and high boiler efficiency. b. Marine Boiler is utilized as a source of motive power for ships. KLM Technology Group Rev: 01 These design guideline are believed to be as accurate as possible, but are very general and not for specific design .

lexie@zozen.com > Get A Quote >

Steam Boiler - Definition, Working Principle, Types, an

The capacity of the boiler to have steam, as well as water is sufficient. Generally, the liquids are stored in the boiler for generating steam by burning the fuels or applying the heat energy at different conditions of pressure based on the size of the vessel as well as specifications. These boilers have membrane design and operate

lexie@zozen.com > Get A Quote >

30 t/h waste heat steam boiler – Industrial Boil

Water tube boilers have a capacity of up to 120 t/h of saturated or superheated steam. In a waste heat boiler, steam is generated from the waste heat of a gas turbine or gas China Condensing Waste-Heat Recovery Steam Boiler – China China Condensing Waste-Heat Recovery Steam Boiler, Find details about China Condensing Waste-Heat Recovery

lexie@zozen.com > Get A Quote >

Steam Boiler - Wet Back Design Gas Fired Boile

Steam Boiler Offering you a complete choice of products which include wet back design gas fired boiler, hybron skid mounted boiler, fire tube type oil fired boiler, urjex make external furnace steam boiler, agro waste fired steam boiler and horizontal wet back oil steam boiler.

lexie@zozen.com > Get A Quote >

Johnston Boiler Company Boiler Glossary - Steam & Combusti

Steam Boilers & Appurtenances, Combustion & Instrumentation Controls, Deaerators, Exhaust Systems, Heat Exchangers, Heat Pipes, Industrial Pumps, Water Heaters, Water Softeners, Boiler Seminars, Services & Parts. 3 Common Boiler Formulas BOILER HORSE POWER What is the boiler horsepower of a boiler generating 21,500 lbs of steam per hour at 155 psi?

lexie@zozen.com > Get A Quote >

Gas & Steam Boil

2.The steam boiler have horizontal structure,so the thermal efficiency is higher; 3.It has the three returns design, so exhausted smoke temperature is low; 4.Adopting the latest technology, it is designed with a combustion chamber with large volume.It is equipped with a world-known burner,making the combustion more sufficient and ensuring

lexie@zozen.com > Get A Quote >

Boiler Capacity - Engineering ToolB

Boiler load - the capacity of a steam boiler - is often rated as boiler horse powers, lbs of steam delivered per hour, or BTU. Lbs Steam delivered per Hour. Large boiler capacities are often given in lbs of steam evaporated per hour under specified steam conditions. BTU - British Thermal Units

lexie@zozen.com > Get A Quote >

Steam Boiler Capacity Calculation--Z

Whether you need a boiler for school, brewery, hotel, textile industry, paper plant or whatever, please tell us your specific information first, and we will calculate the boiler capacity for you. Any questions about industrial steam boiler capacity calculation, please contact with our online customer service.

lexie@zozen.com > Get A Quote >