uses of plc in a boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages

uses of plc in a boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.

uses of plc in a boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
uses of plc in a boiler uses of plc in a boiler uses of plc in a boiler

super heated steam boiler automation using p

Boiler Automation using PLC and SCADA development of boiler automation system using PLC, SCADA and sensors so as to maintain the required water level in boiler drum. SCADA system is used to monitor the boiler feed water flow, steam flow rate and water > Get A Quote >

Steam Accumulators and Steam Boiler Response to Load Chang

Fulton Boiler Works, Inc. Fulton Thermal Corporation Steam Accumulators and Steam Boiler Response to Load Changes C. Merritt, Fulton Thermal Corp. Introduction Certain steam-using equipment, when initially placed in service, will use steam at a rate far in > Get A Quote >

Coal Conveyor Belt Fault Detection and Control in Thermal power

taken to the Boiler through coal pipes with the help of hot and cold air mixture. They are more acceptable than other means of transporting bulk materials; they neither pollute the air nor deafen the ears. > Get A Quote >

PLC & SCADA Based Effective Boiler Automation System for

PLC & SCADA Based Effective Boiler Automation System for Thermal Power Plant International Journal of Advanced Research in Computer Engineering & Technology > Get A Quote >

Boiler Feed Pump Control Using Variable Frequency Dri

not so easy, so we use PLC and SCADA system to get control and receive data. 6.1 Programmable logic control (PLC) A PLC is a microprocessor-based control system, designed > Get A Quote >

siemens plc boiler application – zg oil and gas boiol

This site uses cookies in order to improve your user Control system – Wikipedia A control system manages, commands, directs, or regulates the behavior of … > Get A Quote >

What is a PLC. Who uses them and what for? Learn how to progra

What IS a PLC? The letters PLC, in electronic control and automation realms, are an abbreviation and stand for, Programmable Logic Controller "What’s one of those?" I hear! > Get A Quote >

Simulation of boiler using PID controller and Automation (PLC &

PLC controls the boiler temperature and pressure and gives out the user required volume of steam. uses PID controller more than 90%. Design of PID controller still remains a challenge before researchers and engineers.To design and tune the controller to > Get A Quote >

use of steam in oil refinery – Industrial Boiler Suppli

Steam Boiler for Oil Refinery – Steam boilers are one of the most fundamental systems of a oil refinery and use of water in a oil refinery is makeup for boiler feed. The chief uses of steam are for stripping, steam distillation, and vacuum > Get A Quote >

(PDF) Improving Boiler Efficiency Using PLC Controll

PDF | Boiler systems have many factors that affect the efficiency of the air conditioning process. This paper uses Allen Bradley PLC Controllogix 1756 series as a communications equipment. The essential components of the control loop are sensor, an The > Get A Quote >

How Safety PLCs Can Enhance Burner Manageme

The bottom line is if you are using a safety PLC, you do not have to follow the standards for conventional PLCs, In the boiler world, you cannot use the same controller for both, so it must be separated. One minor exception is a single point positioning system > Get A Quote >