touch controller generator

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

touch controller generator have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


touch controller generator.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
touch controller generator touch controller generator touch controller generator

Touch Pad Control System - Steam Generato

Select the desired duration and temperature of your steam bath with SteamSpa's programmable control panel. Controls are included for optional in-shower lighting or the SteamSpa chromotherapy treatment, which uses colored lights to enhance the soothing SteamSpa experience. The programming feature plus memory (optional upgrade) means your settings can also be stored in the panel’s memory for

lexie@zozen.com > Get A Quote >

AUTOMATIC TRANSFER SWITCH CONTROLLER FOR DUAL

timers and setting, and the controller will force-start the second generator and transfer the switch from the current working generator to the second generator. The Bypass function can be activated only in AUTO. LEDs status under Bypass mode 2.3.5 OFF Key Touching the OFF key, turns the ATS-34 OFF engaging a flashing red LED instantly disabling all

lexie@zozen.com > Get A Quote >

Unity - Scripting API: Tou

Devices can track a number of different pieces of data about a touch on a touchscreen, including its phase (ie, whether it has just started, ended or moved), its position and whether the touch was a single contact or several taps. Furthermore, the continuity of a touch between frame updates can be detected by the device, so a consistent ID number can be reported across frames and used to

lexie@zozen.com > Get A Quote >

LP1 Lightplane Touch Controller - Perfect Circu

After a short break 54HP is back with a touch controlled synth voice on episode 7. The only sound generator is a Mutable Instruments Plaits run through a 2HP Verb. The other three modules in the case focus on touch controls. The Intellijel Tetrapad in fader mode has four faders which each output both fader position and pressure.

lexie@zozen.com > Get A Quote >

Fruity Envelope Controller - Generat

Link a hardware controller to control the X and or Y knob (if desired). Finally, move the hardware controller knob/slider and record it OR Record X/Y modulation with a mouse/touch directly on the Fruity Keyboard Controller plugin OR link the Fruity Envelope Controller X/Y knob to another internal controller.

lexie@zozen.com > Get A Quote >

ThermaTouch Controller - Icon(s) are no longer visibl

If you have the Steam Generator + inside Shower Control installed you will see the below icons: If the above devices are not properly connected or there is a communication issue with any devices you may re-scan the system to see what device are online. Here are the steps: Touch on Settings icon Touch on Equipment Touch on Scan For Devices

lexie@zozen.com > Get A Quote >

THERMASOL MTC-SN MicroTouch Controller Contemporar

THERMASOL MTC-SN MicroTouch Controller Contemporary - Satin Nickel Capacitive touch technology (ctt) similar to a smartphone screen Built-in infrared temperature sensor (its) patent pending Thermasol PRO-395 PRO Series Steam Generator size 395 Red/Stainless steel 5.0 out of …

lexie@zozen.com > Get A Quote >

OneTouch Controller - Flashing 60 LED – ThermaSol Solutio

OneTouch Controller - Flashing 60 LED Martin Siwy Updated May 15, 2019 17:33. Follow. This troubleshooting guide will help with "Flashing 60" message your control is displaying. If you steam generator has this ball valve, it should be closed in the 9 o'clock position. You will need to pull the black handle down so it is in the 6 o'clock

lexie@zozen.com > Get A Quote >

4-wire resistive Touch Screen Controller - Ro

BU21021GUL is a resistive touch screen controller, which is capable of detecting 2 points touch with a legacy 4-wire resistive touch screen. It is composed of 32-bit CPU, 12-bit SAR A/D converter, clock oscillator, and voltage regulators power supply, and operates at a …

lexie@zozen.com > Get A Quote >

Generator Controller | eB

Find great deals on eBay for Generator Controller in Generator Parts and Accessories. Shop with confidence. Find great deals on eBay for Generator Controller in Generator Parts and Accessories. (Manual, Auto, Stop), can pass panel light touch buttons artificially start/stop genset, also can. through remote start signal input automatic

lexie@zozen.com > Get A Quote >

EETI - distec.

EXC80H60 is a MCU based projected capacitive touch screen controller designed for commercial and industrial application. EXC80H60 controller supports high voltage driving signal to achieve high SNR and better wideband interference susceptibility. EXC80H60 needs an external DC/DC booster chip to generate high voltage.

lexie@zozen.com > Get A Quote >