common power plant boilers

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

common power plant boilers have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


common power plant boilers.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
common power plant boilers common power plant boilers common power plant boilers

Boiler Tube Leakage detection by Acoustic Instrument i

Introduction – Boiler Tube Leakage. Boiler tube leakage is the major cause of outage of units and generation loss in thermal power plants. Detection of boiler tube leakage is a very important factor for power plant functioning as approximately 60% of boiler outages are due to tube leaks.

lexie@zozen.com > Get A Quote >

Power Plant Boilers: Condenser Performance Monitorin

The steam condenser of a power plant boiler is a critical heat exchanger in the process. Poor performance due to restricted heat transfer can have a dramatic influence on unit efficiency. And

lexie@zozen.com > Get A Quote >

Life to Boilers Summary - abma.c

Power plants and boilers in particular have an expected (and have achieved) long‐duration operational life, typically exceeding their specified Design Life expectations. Power plants and boilers are a major capital expenditure and the most common understanding (or interpretation) of specification

lexie@zozen.com > Get A Quote >

Typical Causes of Slagging and Fouling Problems in Boile

Boiler slagging and fouling are some of the major operations and maintenance factors that can negatively affect power plant the most common causes of maintenance headaches at coal-fired power

lexie@zozen.com > Get A Quote >

Biomass Cofiring in Coal-Fired Boile

energy needs. The most common types of biomass that are available at potentially attractive prices for energy use at federal facilities are waste wood and wastepaper. One of the most attractive and easily implemented biomass energy technologies is cofiring with coal in existing coal-fired boilers. In biomass cofiring, biomass can substitute for up

lexie@zozen.com > Get A Quote >

What Types of Fuel Used in Power Plant Boil

The most common fuel types used in power plant boiler systems are as follows: Coal. Most industrial coal-fired boilers run on crushed coal, which burns more efficiently than large coal clumps. Gas and Oil. Gas-fired boilers operate using natural gas, most often a …

lexie@zozen.com > Get A Quote >

THERMAL POWER PLANTS: BOILER WATER TREATMENT,SCALE

5/12/2011 · B) High pressure boilers will be found in industry, generating steam for a variety of uses, locomotion via a steam engine, or for end use of steam in laundries, rubber product manufacturing, wood pulp products, food manufacture etc. These boilers operate at over 10 psi and all require constant "make up" water as some of the steam is used.

lexie@zozen.com > Get A Quote >

Common Boiler Fuel Types | Miura Boile

Finally, some boilers forsake the more traditional types of fuel altogether in favor of biomass. These are less common fuel types applied by environmentally progressive companies that utilize items like wood chips, corn husks, and various plant materials that surprisingly can be used to fuel boilers.

lexie@zozen.com > Get A Quote >

Condensation Electric Power Plant | Article abou

Condensation Electric Power Plant a thermal steam-turbine power plant whose purpose is the generation of electric power by condensing turbines. A condensation electric power plant uses organic fuels (solid fuels, mainly pulverized coal of various types, as well as mazut). The heat released by combustion of the fuel is transmitted to a working substance

lexie@zozen.com > Get A Quote >

boilers and power plants in india intech - unic.co.

Power Plant Boiler Market is projected to reach USD 24.40 Nov 30, 2018 · The power plant boilers using coal as fuel are estimated to hold major share of the power plant boiler market. The coal based boiler market is primarily driven by Asian countries, namely, China and India which make up for more than 50% of the coal fuel based boilers.

lexie@zozen.com > Get A Quote >

Boiler Feed Water Treatment for Industrial Boilers an

The vibratory shearing process has two major applications in the power plant. The first is processing of boiler water influent. To avoid boiler scale, power plants usually utilize a multi-step process to remove hardness of incoming water, including either chemical treatment or ion exchange and several less advanced methods such as multimedia filtration.

lexie@zozen.com > Get A Quote >