diesel boiler manufacturers bangalore

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

diesel boiler manufacturers bangalore have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


diesel boiler manufacturers bangalore.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
diesel boiler manufacturers bangalore diesel boiler manufacturers bangalore diesel boiler manufacturers bangalore

Steam Generators, Low Pressure Boiler - Ultimate Wash

A steam generator is used as a source of heat for thawing and de-icing aggregates. This low pressure boiler also speeds up the curing process for pre-cast concrete, pipe, pre-stress, block operations, saturating the curing area with steam, uniformly heating the …

lexie@zozen.com > Get A Quote >

What You Need to Know About Residential Steam Boile

The steam boiler is an old convection heating technology dating back over 200 years and is commonly found in older homes. Because steam boilers operate at a higher temperature than hot water boilers they are inherently less efficient than their hot water cousins.

lexie@zozen.com > Get A Quote >

4 things to look out for in steam boiler pressure control

9/28/2016 · The boiler operating control is set at the desired steam pressure of the boiler. On-off steam systems for comfort heating are usually set for an average of 2 lb. of steam pressure. The operating control is an automatic one that will cycle the boiler between the settings of the pressure control as long as there is a call for heat.

lexie@zozen.com > Get A Quote >

P47 Series Steam Pressure Limit Controls Installatio

required) between the boiler and the control so live steam does not enter the bellows corrugation. (A siphon is not supplied as standard with 0 to 15 psig [0 to 103 kPa] range controls.) 3. The P47 control must be mounted to a tap separate from the pressure gauge or other devices. Refer to Fig. 2 for typical P47 mounting. 4.

lexie@zozen.com > Get A Quote >

HP603 - Boiler Control Settings - Burnham Commerci

• Improved boiler life: Low high low or modulating burners allow for a more stable temperature change in the boiler when transitioning from low to high fire. Some incorporate a low fire hold feature to provide a more gradual change from lower water temperatures or steam pressures to higher operating temperatures or pressures.

lexie@zozen.com > Get A Quote >

Boiler (power generation) - Wikiped

A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.

lexie@zozen.com > Get A Quote >

Selecting the Optimum Steam Pressure for Process Applicatio

Steam 80 psi pressure that is provided to the equipment manufacturer for design of the process heat transfer. 80 psi shall be the pressure after the steam control valve or the steam pressure that can be delivered to the process. Example: Process temperature requirements are 310°F; using the steam tables locate the correspond-ing steam pressure. 1.

lexie@zozen.com > Get A Quote >

Difference Between Low- and High-Pressure Boilers | Hunk

A boiler is an appliance designed to heat water and produce energy. The heat is applied to water in an enclosed container before being distributed throughout the system. The major difference between a low-pressure and a high-pressure boiler is the amount of pressure per square inch and pounds per square inch gauge that the boiler produces.

lexie@zozen.com > Get A Quote >

Steam Pressure Reduction: Opportunities and Issu

Steam Pressure Reduction: Opportunities and Issues varies directly in proportion to the boiler’s net stack temperature (the difference between the flue gas tem-perature and combustion air temperature). When boiler pressure is lowered, a lower stack temperature results. This, in turn, causes slightly improved combustion efficiency.

lexie@zozen.com > Get A Quote >

Steam System Design and Best Practices Related to Kiln Dryi

Steam Boiler – high or low pressure Typical Steam Main Drip Station. New England Kiln Drying Association – Steam Design & Best Practices – HerLine Technologies Steam …

lexie@zozen.com > Get A Quote >

High Pressure Condensate Receiving Syste

Results Implementing a High Pressure Condensate System and instituting the New Operating Conditions Once a new high pressure condensate system is installed, typical losses will be greatly reduced and the high pressure condensate from the steam press will operate nominally at 125 psi @ 353°F. Swagelok Energy Advisors, Inc. STEAM SYSTEMS BEST

lexie@zozen.com > Get A Quote >