industrial induced fan data sheet for boilers

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

industrial induced fan data sheet for boilers have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


industrial induced fan data sheet for boilers.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
industrial induced fan data sheet for boilers industrial induced fan data sheet for boilers industrial induced fan data sheet for boilers

Furnace - Wikiped

An industrial furnace or direct fired heater, is an equipment used to provide heat for a process or can serve as reactor which provides heats of reaction. Furnace designs vary as to its function, heating duty, type of fuel and method of introducing combustion air. However, most process furnaces have some common features.

lexie@zozen.com > Get A Quote >

Technical Datasheet - Tarm Bioma

Specification Data 4 P4 Pellet Dimensions Component Unit 8 / 15 20 / 25 32 / 38 48/60 L Length, boiler 1) inches 29⅛ 29⅛ 32¼ 35½ L1 Total length inc. induced draught fan 37 37 40⅛ 43¼ B Width, boiler inches 23⅝ 30⅜ 33¾ 40½ B* Width, boiler, inc. support for posi-tioning unit 2) 27¾ 34½ 38 50¼

lexie@zozen.com > Get A Quote >

(PDF) Case Study: Optimization of an Industrial Stea

Case Study: Optimization of an Industrial Steam Boiler System Operation For industrial boilers, the load of the induced-draft fan increases and prevents the boiler to reach its normal

lexie@zozen.com > Get A Quote >

FMDS0604-Oil- and Gas-Fired Single-Burner Boilers_

This data sheet does not apply to natural draft boilers; refer to ASME CSD-1, Controls and Safety Devices for Automatically Fired Boilers. This data sheet also does not apply to boilers 2,500,000 Btuh (732 kW) or less that are listed by a nationally recognized testing laboratory agency.

lexie@zozen.com > Get A Quote >

Twin City Fan & Blower HVAC Fans and Blowers Data Sheet

Twin City Fan & Blower Datasheets for HVAC Fans and Blowers HVAC fans and blowers are used to move air through heating, ventilating, and air conditioning (HVAC) systems. They are an integral part of the air handling systems that bring or draw fresh air into buildings.

lexie@zozen.com > Get A Quote >

Boiler Centrifugal Induced Fan - seekpart.c

Y5-47 boiler centrifugal induced fan has the features It is suitable for industrial boiler in which there are smoke-exhausting set .The medium air should be in temperature of less than 250 deg C.It is driven in type C and D.It is matched with air volume adjusting set.If vibration absorber is used,clients can lay the fans on the earth directly without any earthing screw.It is easy to install

lexie@zozen.com > Get A Quote >

Alloy steel industrial boiler ventilation draft blow

(YN5-47) Induced Draft Fan Centrifugal Blower Fan for Boiler YN5-47 Industrial Centrifugal Blower/ Boiled Induced Draft Fan for dust exhaust/ ventilation high temperature resistance 180-200ºC 1. The motor is made of Y2 aluminum alloy die-casting material, greatly reducing the weight, convenient installation and beautiful appearance. 2. Get Price

lexie@zozen.com > Get A Quote >

combined cycle with heat recovery boiler - emetreinta.

Waste heat recovery technologies and applications . 2. Waste heat recovery systems. Waste heat recovery methods include capturing and transferring the waste heat from a process with a gas or liquid back to the system as an extra energy source .The energy source can be used to create additional heat or to generate electrical and mechanical power ..

lexie@zozen.com > Get A Quote >

Chinese Boiler Supplier - emetreinta.

local laundry boilers manufacturers; 6T H Gas Steam Boiler; vacuum hot water boiler supplier; industrial induced fan data sheet for boilers; gujarat boiler online for sale; vaporax steam boiler; foster wheeler boiler spare part supplier; Oil Fired Boiler Manu In India; boiler making companies in south africa; boilers which we can use in power

lexie@zozen.com > Get A Quote >

Blowers | Emerson

Manage Fan and Blower Health in Real Time If a blower or induced-draft fan on a fired heater, furnace, or reformer develops a problem before the next scheduled inspection, the reliability of your plant can suffer. A unit could fail unexpectedly and cause a slowdown, or worse, a shutdown.

lexie@zozen.com > Get A Quote >

Industrial Boilers | Mill (Grinding) | Boiler - Scri

BOILERS. What is a Boiler? Vessel that heats water to become hot water or steam At atmospheric pressure, water volume increases 1,600 times when it gets converted to steam Industrial Boilers Steam generators Closed vessels made of steel and used for generation of steam by vaporizing water combustion of fuels like coal, coke, oil, wood, saw dust Steam used for producing power industrial …

lexie@zozen.com > Get A Quote >