industrial boiler mact 2011

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

industrial boiler mact 2011 have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


industrial boiler mact 2011.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
industrial boiler mact 2011 industrial boiler mact 2011 industrial boiler mact 2011

Meeting MACT Compliance: Are you read

What the EPA says and key facts: The industrial MACT ruling places limits on the following: (All) Dioxin/Furans Particulate matter (as a surrogate for non-mercury metals) Carbon monoxide (as a surrogate for non-dioxin organic air

lexie@zozen.com > Get A Quote >

EPA industrial boiler MACT rules to be released |

Follow us on Facebook Follow us on Twitter Connect with us on Linked In Follow us on Instagram Email Bracewell Law

lexie@zozen.com > Get A Quote >

Industrial Boiler MACT Rule - The McIlvaine Compa

Anticipated Industrial Boiler ACI System MACT Compliance Timeline Testing & Evaluation 1/2010 –12/2011 Compliance Strategy, Eng, & Specifications by Customers 12/2010 –12/2011 Place ACI Equipment Orders 6/2011 –6

lexie@zozen.com > Get A Quote >

Boiler MACT Requirements Summary 1-8-13 - CI

December 2012 Boiler MACT Reconsidered Rule Requirements Summary, Prepared 1/8/13 Page 1 of 18 Industrial Boiler MACT Reconsideration Rule Requirements Summary Federal Regulation: • NESHAP 40

lexie@zozen.com > Get A Quote >

PRESS RELEA

FOR IMMEDIATE RELEASE CONTACT: Marnie Satterfield February 28, 2012 (202) 223-1420 [email protected] “U.S. Senate Fails to Help Manufacturing” Industrial Boiler MACT Is reducing the cost of compliance

lexie@zozen.com > Get A Quote >

Boiler MACT Compliance - Nationwide Boiler In

Learn more about Boiler MACT and how Nationwide Boiler can help! Nationwide Boiler Inc. Home Rentals Trailer-Mounted Boilers

lexie@zozen.com > Get A Quote >

AISI Says Changes Reflect Progress on Boiler MACT Rul

2011 2010 2009 2008 2007 2006 2005 2004 2003 Sustainability AISI Says Changes Reflect Progress on Boiler MACT Rules Washington, D.C., 2/24/2011 - American Iron and Steel Institute (AISI) President and CEO Thomas

lexie@zozen.com > Get A Quote >

EPA’s Boiler MACT Rules Still a Threat - Amazon

of Industrial Boiler Owners,2 put the figure at $20 billion. The U.S. Small Business Administration warned that the rules would cause “significant new regulatory costs” for businesses, institutions, and municipalities across the 3 4

lexie@zozen.com > Get A Quote >

EPA Proposed New MACT Rules for Industrial Boiler

2012/01/18 · On Dec. 23, 2011, the United States Environmental Protection Agency (EPA) proposed changes to the National Emission Standards for Hazardous Air Pollutants for Major Sources: Industrial, Commercial and Institutional

lexie@zozen.com > Get A Quote >

EPA Proposes “Franken-MACT” for Utilities | Trinity

On May 3, 2011, EPA published the highly anticipated proposed Maximum Available Control Technology (MACT) Standard for the utility sector (40 CFR 63 Subpart UUUUU). When considered together with the growing list of proposed

lexie@zozen.com > Get A Quote >

www.awc.o

organic HAP,” but concluded for purposes of the Industrial Boiler MACT that D/F should be regulated separately “because, unlike other organic HAP, D/F can be formed outside the combustion unit.” Id. The proposed standards for

lexie@zozen.com > Get A Quote >