moisture steam generator

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

moisture steam generator have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


moisture steam generator.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
moisture steam generator moisture steam generator moisture steam generator

Development of Moisture Separator With High

Download Citation on ResearchGate | Development of Moisture Separator With High Performance of Steam Generator | A steam generator of PWR plant has moisture separators with function to separate water from two-phase flow of

lexie@zozen.com > Get A Quote >

STEAM GENERATORS, NUCLEAR - A-to-Z Guide t

Reactor coolant enters the steam generator at the inlet nozzle (on the bottom left-hand side of Figure 2) and enters the tube bundle in the hot leg, completing the U-bend through the cold leg to the primary outlet. Feedwater enters the

lexie@zozen.com > Get A Quote >

Moisture separator for steam generator level

1987/12/29 · A steam generator level measurement system of the type having a reference leg which is kept full of water by a condensation pot, has a separator pot in the connecting line between the condensation pot

lexie@zozen.com > Get A Quote >

Secondary Systems: Steam System - NPT

NPTEL - Chemical Engineering - Nuclear Reactor Technology Joint Initiative of IITs and IISc – Funded by MHRD Page 1 of 10 Secondary Systems: Steam System NPTEL - Chemical Engineering - Nuclear Reactor Technology

lexie@zozen.com > Get A Quote >

Memprediksi Performa Steam Turbine Generator

Y = % moisture pada ELEP Packing & Valve Steam Leakage flow Untuk menentukan power output steam turbine generator, tentu harus dihitung juga kebocoran/leakage steam yang terjadi. Leakage tersebut terjadi pada F = C 0.5

lexie@zozen.com > Get A Quote >

Moisture Generator Wholesale, Generator Suppliers -

Alibaba.com offers 619 moisture generator products. About 21% of these are petroleum additives, 20% are paper chemicals, and 5% are facial steamer. A wide variety of moisture generator options are available to you, such as free

lexie@zozen.com > Get A Quote >

Moisture Separator Reheaters |MSR Reheaters | GE

With our service experience of more than 175 retrofits and installation of 270 new moisture separator reheaters (MSRs), GE technology can improve efficiency As an integral part of the turbine generator package, the MSR

lexie@zozen.com > Get A Quote >

Moisture Ingress from Direct Cycle Steam

Form 412.09 (Rev. 10) Idaho National Laboratory MOISTURE INGRESS FROM DIRECT CYCLE STEAM GENERATION—EFFECT ON FUEL PERFORMANCE AND FISSION PRODUCT TRANSPORT TECHNOLOGY

lexie@zozen.com > Get A Quote >

atomic power review: Steam Generators: Design and

While No. 2 plant did have some steam generator tubes plugged as a part of normal work, and there appears to be no commonality between the few leaking tubes at No. 2 and the leaks at No. 3, SCE has decided to be cautious

lexie@zozen.com > Get A Quote >

Chapter 17 - Measurement Of Steam Purity | SU

Impurities Methods of steam purity measurement Representative steam sampling Accurate measurement of steam purity is essential to identifying the cause of potential or existing steam purity problems in modern boiler plants. One

lexie@zozen.com > Get A Quote >

CHAPTER5 STEAM, TURBINE AND FEEDWATE

CANDUOverview Dr. George Bereznai CHAPTER5 Chapter 5: Steam, Turbine andFeedwater page 5 -J STEAM, TURBINE AND FEEDWATER CHAPTER OBJECTIVES: At the end ofthis chapter, you will beable to describe the

lexie@zozen.com > Get A Quote >