hot oil heat transfer boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

hot oil heat transfer boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


hot oil heat transfer boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
hot oil heat transfer boiler hot oil heat transfer boiler hot oil heat transfer boiler

Heat transfer plants: Thermal oil systems are the righ

Heat transfer plants are suitable nowadays in almost all producing branches. Owing to their working fluid (the so-called „heat transfer medium“, named generally also “heat transfer oil”, “thermal oil” or “thermo oil”) these plants are designated in many cases also as “thermal oil plants”, “hot oil plants” or “thermo oil heating plants”or “hot oil units”.

lexie@zozen.com > Get A Quote >

Hot Oil System Cleaning & Flushing | Paratherm Hea

Heat transfer fluids for processing applications, process manufacturing, process heating and cooling, system assistance and troubleshooting, call (800) 222-3611 paratherm.com describes 9 heat transfer fluids ranging from -88 degrees C up to 343 degrees C, with detailed fluid properties, tables, ranges, and …

lexie@zozen.com > Get A Quote >

Heating Thermic Oil Heat Transfer Boil

Electric heating hot oil boiler (also known as heat conduction oil heater), the electric heater is directly inserted into the thermal oil (heat conduction oil) for direct heating. A circulating pump is used to create liquidphase circulation of heat conduction oil, thus, to transfer the heat to one or several pieces of heat using equipment.

lexie@zozen.com > Get A Quote >

How the Thermal Oil Boiler Works - LPS Filtrati

8/8/2017 · How the Thermal Oil Boiler Works. By admin August 8, 2017 Thermal Oil thermal fluid, hot oil heater, hot oil system, and hot oil boiler. All of them refer to the same type of closed loop liquid phase heat transfer system. And many people use the terms thermal oil boiler or thermal fluid boiler even though most systems do not involve any

lexie@zozen.com > Get A Quote >

Hot Oil Heating Systems - Hot Oil Heaters | Heat Exchang

Heat Exchange and Transfer, Inc. designs and manufactures a hot oil heating systems that are available in large capacities, and 550⁰F, 650⁰F, and 750⁰F using a wide range of heat transfer fluids.Our hot oil heaters are used in a variety of industries including aerospace, defense, energy, and pharmaceutical. Request your quote today!

lexie@zozen.com > Get A Quote >

3 Reasons to Use a Hot Oil Heater | Best hot oil boiler

12/7/2016 · In cases like this using a specialty heat transfer fluid (or hot oil) is a clear solution. By picking a heat transfer fluid with a higher maximum film temperature – maybe 600°F – you can feel comfortable heating it directly in the heater, and using the hot fluid in an exchanger to warm the amine in a more controlled environment that is

lexie@zozen.com > Get A Quote >

Heat Transfer Fluid - Watt

Heat Transfer Fluid vs. Lubricating Oil Heat Transfer Fluids & its Many Types Flanged heaters are used in processing industires to heatup heat transfer fluids. In industrial and engineering terms, Heat Transfer Fluid is also known as coolant. Just as the name suggested, it is …

lexie@zozen.com > Get A Quote >

Steam Boiler Hot oil Heater Heat Exchanger - STEAMASTER C

STEAMASTER CO LTD, leads in the specialized area of Industrial Heating, hot oil Heater and steam boiler, Heat Exchanger technology with innovative trends. STEAMASTER solutions in partnership with our customers, helps to assure our customers of a competitive edge in their area of business

lexie@zozen.com > Get A Quote >

DOWTHERM™ and SYLTHERM Heat Transfer Flui

DOWTHERM™ MX heat transfer fluid is a mixture of alkylated aromatics and is designed for use as an alternative to hot oils in liquid-phase heat transfer systems. The normal operating temperature range for DOWTHERM MX fluid is -23°C (-10°F) to 330°C (625°F). DOWTHERM™ Synthetic Organic and SYLTHERM† Silicone Heat Transfer Fluids

lexie@zozen.com > Get A Quote >

Hot Oil Filtration - multitherm.c

The Benefits of Hot Oil Filtration Improving service life of heat transfer fluids - and your equipment. Heat transfer fluids degrade primarily by thermal cracking and oxidation. 100 mesh strainers are installed on the pump suction line to protect and reduce wear on the pump.

lexie@zozen.com > Get A Quote >

Hot oil boilers,hot oil heaters,thermal oil boile

Established in 1992, Romiter Group Limited are committed to manufacturing and exporting complete enery saving heating equipment, including thermal oil boiler (Thermal fluid heat transfer product), thermal oil steam generator, cryogenic storage Dewar. As we know, both water and steam are used as heat carriers in process heating systems.

lexie@zozen.com > Get A Quote >