cement plant heater

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

cement plant heater have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


cement plant heater.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
cement plant heater cement plant heater cement plant heater

Pearson Systems | Concrete Heaters and Chille

Simple, efficient, rugged, reliable, and designed specifically for concrete plants Dozens of configurations can be custom built for your specific water heating demands and plant layout: seven different burner sizes, U.L.-approved burner operates on #2 fuel oil, natural gas, propane or combination of gas and oil, and high volume multi-burner units are available

lexie@zozen.com > Get A Quote >

Preheater Cyclone In Cement Plant - X

Preheater Cyclone In Cement Plant As a global leading manufacturer of products and services for the mining industry, our company can provide you with advanced, rational solutions for any size-reduction requirements, including quarry, aggregate, grinding production and complete plant plan.

lexie@zozen.com > Get A Quote >

WASTE HEAT RECOVERY POWER PLANTS IN CEMENT

WASTE HEAT RECOVERY POWER PLANTS IN CEMENT INDUSTRY S K Gupta / S K Kaul Holtec Consulting Private Ltd., Gurgaon, India ABSTRACT In a cement plant, nearly 35% heat is lost, primarily from the preheater and cooler waste gases.

lexie@zozen.com > Get A Quote >

Pre-Heater Fan Coating - Page 1 of

The study entailed two approaches: 1) information gathering and 2) a laboratory simulation of cement plant build-up conditions. In the first case, information from several cement plants was collected to determine if a pattern of conditions leading to build-up could be identified.

lexie@zozen.com > Get A Quote >

Preheater - KHD Internation

KHD is a customer-focused engineering, equipment supplier, and service company, providing a full-line of competitive and environmentally friendly technologies to the cement industry. KHD, founded back in 1856, is a global leader in cement plant technology, equipment, and services and hence, the right partner for all your demands.

lexie@zozen.com > Get A Quote >

Cement Plants – Structural Engineering Solutio

Our professional staff has an extensive experience in damage assessment, structural evaluation, repairs and design of various structures in cement plant facilities worldwide. This includes: Silos; Pre-heater Towers; Kiln Supports; Vertical Mill Foundations; Transfer Towers; Conveyors; Inspections and …

lexie@zozen.com > Get A Quote >

The cement kiln - Understanding Ceme

However, new cement kilns are of the 'dry process' type. Dry process kilns. In a modern works, the blended raw material enters the kiln via the pre-heater tower. Here, hot gases from the kiln, and probably the cooled clinker at the far end of the kiln, are used to heat the raw meal. As a result, the raw meal is already hot before it enters the kiln.

lexie@zozen.com > Get A Quote >

Waste Heat Recovery for Power Generation | Industria

Waste Heat Recovery for Power Generation. This heat can be used for electricity production. Power can be produced by using a steam cycle, an organic rankine cycle, or the KALINA process. The low temperature level of the waste heat in cement plants (200 – …

lexie@zozen.com > Get A Quote >

Cement manufacturing - components of a cement pla

Cement manufacturing: components of a cement plant. This page and the linked pages below summarize the cement manufacturing process from the perspective of the individual components of a cement plant - the kiln, the cement mill etc.. For information on materials, including reactions in the kiln, see the ' Clinker ' pages.

lexie@zozen.com > Get A Quote >

Cement kiln - Wikiped

The manufacture of cement clinker. This is called clinker. The hot clinker next falls into a cooler which recovers most of its heat, and cools the clinker to around 100 °C, at which temperature it can be conveniently conveyed to storage. The cement kiln system is designed to accomplish these processes .

lexie@zozen.com > Get A Quote >

Waste Heat Recovery in Cement plant – IJE

In cement plant the exit gases from Rotary kilns, pre-heater and Calciners are used to heat the incoming feed material and gases are cooler around 300 to 350 °C in 4 stage pre-heater and then exhausted to the atmosphere.

lexie@zozen.com > Get A Quote >