boiler bs 2790

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

boiler bs 2790 have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


boiler bs 2790.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
boiler bs 2790 boiler bs 2790 boiler bs 2790

BS_2790_1992_,_Specification_for.pdf | Boiler (365 view

BSI 02-2000 v BS 2790:1992. Foreword. This British Standard, first published in 1956 under the title Cylindrical land steam boilers of welded construction, superseded by BS 2790-1 in 1969 and BS 2790-2 in 1973, and subsequently revised in 1982, 1986 and 1989, has been prepared under the direction of the Pressure Vessel Standards Policy Committee.

lexie@zozen.com > Get A Quote >

B33101 - Boiler Code - ATH

1975 Marine Department Boiler Code and the British Standard 2790 Part 1 - 1969 Metric Boiler Code. Inspections Every boiler, subject to these rules must be inspected once in each year, (unless approved for 2 yearly inspection) by a Boiler Inspector who, when he has completed the Inspection and is satisfied that the boiler is in good repair and may

lexie@zozen.com > Get A Quote >

BS 2790:1992|British Standar

Buy a PDF Download or Hardcopy of British Standard BS 2790:1992, Specification for design and manufacture of shell boilers of welded construction

lexie@zozen.com > Get A Quote >

Design Codes - Plant - Health and Safety Executi

Design Codes - Plant. The design of the furnace or boiler enclosure should be able to withstand the thermal conditions associated with the system and specialist designs are often required. Many codes and standards exist for boiler design. BS 2790: 1992 - Specification for design and manufacture of shell boilers of welded construction.

lexie@zozen.com > Get A Quote >

MAXITRAK & STEAM TEHCNOLO

MAXITRAK & STEAM TEHCNOLOGY round the boiler except in the firebox where the weld is inside the water jacket. We do not use ordinary commercial rivets for boiler stays as they are of unknown (BS 1113) EN 12953 (BS 2790) EN 13480 (806) Welding Procedures Qualification BS EN 288 and ASME IX

lexie@zozen.com > Get A Quote >

Harpur Hill, Buxton, SK17 9JN Telephone: 0129 821 82

PES in boiler control and the recently published standards, e.g., BS EN 61508, which cover these technologies. This report is the second in a series of reports and describes methodologies for allocating the SILs1 between safety functions, and is intended to provide some of the information that will allow a state-of-the-art revision of PM5 to be

lexie@zozen.com > Get A Quote >

boiler bs 2790 – zg boil

8/21/2018 · BS, BS EN, ISO Standards, IEC Standards and Codes of Practice, etc. shall be The steam boiler shall be constructed to BS 2790:1992 for a maximum. Boilers – WorkSafe. Under 15 hp boilers built to BS 2790:1982, or to later editions of that Standard 60. 4.6 Coupled boilers 60. 4.7 Existing boilers 60. Part 5: Unattended Boilers .

lexie@zozen.com > Get A Quote >

KBV20 Key operated boiler blowdown valve - Spirax Sar

Key operated boiler blowdown valve. 2 The Spirax Sarco key operated blowdown valve BS 1113 - Specification for design and manufacture of water tube steam generating plant. BS 2790 - Specification for design and manufacture of shell boilers of welded construction.

lexie@zozen.com > Get A Quote >

BS 2790, BS 2790 download large discount - pdfsfree.o

Buy PDF Download BS 2790 how to get the big discount $ inspection, non-destructive testing for 3 classes of boiler and pressure testing. Additional information and design and manufacturing considerations details in appendices.

lexie@zozen.com > Get A Quote >

BS 2790:1992 - Specification for design and manufacture o

Purchase your copy of BS 2790:1992 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available online in electronic and print formats.

lexie@zozen.com > Get A Quote >

Shell boilers - Gost-Snip Гостандарт

BRITISH STANDARD BS EN 12953-5:2002 Shell boilers Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler The European Standard EN 12953-5:2002 has the status of a British Standard ICS 27.060.30; 27.100 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

lexie@zozen.com > Get A Quote >