hot water boiler combined heat steam turbine generator

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

hot water boiler combined heat steam turbine generator have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


hot water boiler combined heat steam turbine generator.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
hot water boiler combined heat steam turbine generator hot water boiler combined heat steam turbine generator hot water boiler combined heat steam turbine generator

waste heat boiler and hrsg,heat recovery steam generato

A heat recovery steam generator (HRSG) is an energy recovery heat exchanger that recovers heat from a hot gas stream. It produces steam that can be used in a process (cogeneration) or used to drive a steam turbine (combined cycle). The term HRSG refers to …

lexie@zozen.com > Get A Quote >

Steam Turbine CHP Generators - The Renewable Energy H

Steam Turbine CHP Generators. These use high-pressure steam in a constant flow which is generated in a boiler to drive the turbine. Electrical efficiency is maximised when the steam is condensed and pumped back to the boiler as hot water just below boiling point. The thermodynamic cycle is …

lexie@zozen.com > Get A Quote >

Combined Cycle Plant for Power Generation- Introducti

The term “combined cycle” refers to the combining of multiple thermodynamic cycles to generate power. Combined cycle operation employs a heat recovery steam generator (HRSG) that captures heat from high temperature exhaust gases to produce steam, which is then supplied to a steam turbine to generate additional electric power.

lexie@zozen.com > Get A Quote >

Combined Cycle and Combined Heat and Power Process

electricity and steam. Combined Heat and Power (CHP) plant, sometimes called Co-generation plants, produce both electricity and heat. Heat is extracted as steam or hot water and exported from the system. Combined Heat and Power processes can be applied with conventional steam processes without gas turbines or may also include a Combined Cycle

lexie@zozen.com > Get A Quote >

industrial natural gas steam generator – Alibaba Oil Fire

Call (323) 268-3380 for info.Industrial Application of Gas Turbines (IAGT)HRSG Heat Recovery Steam Generator • Also referred to as waste heat boiler • Cools hot gases –most commonly the exhaust of a gas turbine • Generates steam and …Gas Turbine Generator Sets – Frame 5 Frame 6 …Listed 8/9/2017 48MW CC Power Plant 50Hz. Natural Gas.

lexie@zozen.com > Get A Quote >

Catalog of CHP Technologies, Section 4. Technolog

Section 4. Technology Characterization – Steam Turbines . 4.1 . Introduction . Steam turbines are one of the most versatile and oldest prime mover technologies still in general production used to drive a generator or mechanical machinery. The first steam turbine used …

lexie@zozen.com > Get A Quote >

Cogeneration / Combined Heat and Power (CHP) | Center fo

We boiler manufacturer offer gas oil steam boiler, gas oil hot water boiler, fire tube gas oil boiler, water tube gas oil boiler, gas oil power plant boiler . 2 ton gas and oil fired boilers Sri Lanka Boiler maintenance will help you save on overall costs. Maintenance is advised …

lexie@zozen.com > Get A Quote >

Boiler (power generation) - Wikiped

The steam generator or boiler is an integral component of a steam engine when considered as a prime mover. However it needs to be treated separately, as to some extent a variety of generator types can be combined with a variety of engine units. A boiler incorporates a firebox or furnace in order to burn the fuel and generate heat.

lexie@zozen.com > Get A Quote >

steam turbine generator and boiler – Industrial Boile

The turbine usually drives a generator that turns the work from the turbine into electricity. The steam, used by the turbine, can . Boiler (Steam Generator) – Coal Fired Power Plant – Thermal … A boiler or Steam Generator (prime mover) is an integral device in a fossil fuel power plant used to produce steam by applying heat energy to water.

lexie@zozen.com > Get A Quote >

hot water boiler combined heat steam turbine generat

waste heat boiler and hrsg,heat recovery steam generator . A heat recovery steam generator (HRSG) is an energy recovery heat exchanger that recovers heat from a hot gas stream. It produces steam that can be used in a process (cogeneration) or used to drive a steam turbine (combined cycle). The term HRSG refers to the waste heat boiler in a Combined

lexie@zozen.com > Get A Quote >

Datasheet - gas turbines GJZ - CIB

The mass of an 80 kWe micro-turbine CHP package is about 2 tonnes. In general, HV (11 kV) generators will be used above 2 MWe. Waste heat recovery Hot exhaust gases from the GT will be fed into a heat recovery steam generator (HRSG) or hot water for use in the building or process. The main advantage of a gas-turbine CHP system over an IC engine

lexie@zozen.com > Get A Quote >