boiler with amse

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

boiler with amse have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


boiler with amse.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
boiler with amse boiler with amse boiler with amse

ASME BPVC 2017: Power boilers | IHS Mark

ASME BPVC 2017: Power Boilers. The term “power boiler” in this Section includes stationary, portable, and traction type boilers, but does not include locomotive and high temperature water boilers, nuclear power plant boilers, heating boilers, pressure vessels, or marine boilers.

lexie@zozen.com > Get A Quote >

ASME B31.3 Process Piping Guide - engstandards.lanl.g

LANL Engineering Standards Manual PD342 Chapter 17 Pressure Safety Section D20-B31.3-G, ASME B31.3 Process Piping Guide Rev. 2, 3/10/09 4 The Owner and Designer are responsible for compliance with the personnel and process qualification requirements of the codes and standards. In particular, the application of ASME B31.3 requires compliance with the Inspector qualification

lexie@zozen.com > Get A Quote >

Technical Standards & Safety Authority Boilers an

Anyone, or any company, intending to design, fabricate, and install a boiler, pressure vessel, fitting or piping system for installation in Ontario should first refer to the Technical Standards and Safety Act (Act) and Regulations for Boilers and Pressure Vessels (Regulations), which govern such actions.

lexie@zozen.com > Get A Quote >

ASME Codes and Standards for Boiler Inspections - ndt.n

ASME Codes and Standards for Boiler Inspections Michael MOLES Olympus NDT, 48 Woerd Avenue, Waltham, MA, USA 02453 Tel: +1 416 831 4428, E-mail: [email protected]

lexie@zozen.com > Get A Quote >

Relief Valves requirement according to ASME - Boiler an

9/10/2004 · One of our clients pointed out that as per clause No. UG-125 of ASME Sec VIII, Div 1 (see attached), all pressure vessels designed as per ASME, should be provided with relief valves.

lexie@zozen.com > Get A Quote >

Research Article DESIGN OF PRESSURE VESSEL USING

International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974 IJAERS/Vol. I/ Issue II/January-March, 2012/228-234 Research Article …

lexie@zozen.com > Get A Quote >

Boilers & Pressure Vessels - TS

Boilers & Pressure Vessels BPV Certificate of Inspection Our Boilers and Pressure Vessels Safety Program ensures the safe design, construction, maintenance, use, operation and repair of all pressure-retaining components in Ontario.

lexie@zozen.com > Get A Quote >

ASME - The American Society of Mechanical Enginee

ASME’s long-form story. Read the article. Special ASME Journal Issue to Focus on Machine Learning Applications in Manufacturing. The ASME Journal of Computing and Information Science in Engineering is currently accepting manuscripts for a special issue on machine learning applications in manufacturing. Submit electronically by July 1, 2019.

lexie@zozen.com > Get A Quote >

Data Plates, ASME for Steam Boilers - Responsible

Data Plates, ASME for Steam Boilers Regulatory Citation ASME Boiler and Pressure Vessel Code What It Is Standard provides rules for the design, fabrication and inspection of boilers and pressure vessels. Who It Applies To Those directly responsible for operating, maintaining and inspecting steam boilers. Origination Date 1914 ©Compliance Assistance Library 10-10-2014 Data Plates, ASME for

lexie@zozen.com > Get A Quote >

ASME Pressure Vessels | Steel Water Storage Tan

These ASME pressure vessels should be installed at the highest point in the system and will include all necessary openings for controls, valves and gauges. Filter Vessels . Filter Vessels are used in water and waste water treatment systems for removal of suspended solids or contaminants that may be dissolved in the water.

lexie@zozen.com > Get A Quote >

Calendar Of Even

The ASME.ORG Calendar of Events may not be exact. Event dates, times and locations are subject to change. Cancellation of events may occur without notice.

lexie@zozen.com > Get A Quote >