vertical design steam generate boiler

Industrial boilers

Product thermal capacity: 4-35 t/h

Working pressure: 1.0-2.5 MPA

Outlet temperature: 184-350 ℃

Available fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil

Available industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries

  • Product introduction
  • Technical advantages
Introduction

vertical design steam generate boiler have a three-pass round coil structure. A conical coil is used for the effective protection of the furnace wall at the boiler end. This product is equipped with an advanced combustion device and is fully automated in operation. After the burner ignites the fuel, flame fills the round coil tubes and transfers heat by radiation through the tube wall (first pass). The high temperature flue gas gathers at the back door and then turns to the convection tubes section (second pass), where heat transfer takes place by convection. The flue gas gradually cools down here and flows to the front door, where it is reversed and goes into the third pass. After that, it enters into the chimney through the economizer and is released into the atmosphere.


vertical design steam generate boiler.This type of heater is delivered as a whole, and is installed on site, it only needs to connect thermal gas(oil) piping and electricity to start operation. The heater has four heating areas: furnace radiation heating area, the first convection tube bundle heating area, the second convection tube bundle heating area and economizer (waste heat boiler).

Digitized manufacture
  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of round coil tube adopts CNC coil tube automatic production line. Once-forming and no need for plastic .
Full argon arc welding
  • The tube butt adopts argon arc welding technique and the seams will be done x ray real-time imaging, preventing unqualified seams from entering coil production line .
Easy operation
  • Heater is wholly assembled before delivery, it is easy for installation, debugging and operating.
  • Fully automatic operating, burning, liquid level of high level tank, outlet temperature and flow rate are adjusted automatically and self-protected.
  • The inlet and outlet with end flanges and flanged cover structure facilitate the installation and layout of tubeline in boiler house.
Less fuel consumption
  • Internal side adopts good insulation material, outside uses stainless steel plate, which can mostly reduce heat lost and make working environment better.
  • Multilayers closely spaced tube bundle and steel rod is used to seal and fix, completely eradicating short circuit of flue gas.
  • Before delivery, the residue moisture is removed completely, so the system draining period is reduced to 2 days from 12 days.
Safely operation
  • The inner coil tube has bigger flow rate, so it is more stable under high temperature operation.
  • Conical coil effectively protects the furnace wall at the end of heater and burner on the top.
vertical design steam generate boiler vertical design steam generate boiler vertical design steam generate boiler

Balanced Pressure Steam Traps - Spirax Sar

Make your steam system safe, efficient and sustainable with Steam Traps from Spirax Sarco We’ve been in the business of steam solutions for over 100 years and with our exceptional team of specialists, we take the time to understand your needs and work with you to find the most effective steam trapping solutions for your applications.

lexie@zozen.com > Get A Quote >

Steam Generation Suggested Actions - Department of Ener

Benchmarking the fuel cost of steam generation, in dollars per 1,000 pounds ($/1,000 lb) of steam, is an effective way to assess the efficiency of your steam system. This cost is dependent upon fuel type, unit fuel cost, boiler efficiency, feedwater temperature, and steam pressure.

lexie@zozen.com > Get A Quote >

Safety Valves in Boiler System - Bright Hub Engineeri

Safety Valves in Boiler System. Energy & Power Plants / By Dr V T Sathyanathan / Mechanical Engineering. Boilers are high pressure and temperature systems used for generating steam to drive steam turbines for electricity generation. If, due to any reason of operation or malfunction in equipment or controls, the operating pressure in the system

lexie@zozen.com > Get A Quote >

How do I adjust my boiler pressure properly? – Energui

How do I adjust my boiler pressure properly? Your boiler must be at the correct pressure for the hot water to circulate properly between the radiators, especially if they are on different floors. Generally, the ideal pressure is between 1 and 2 bars, but this may vary from boiler to boiler. Ask your heating engineer.

lexie@zozen.com > Get A Quote >

How Power Plant Boiler Works? - brighthubengineering.c

The superheated steam then finally goes to the turbine.Final Superheater temperatures are in the Range of 540 to 570 °C for large power plants and SuperHeated steam pressures are around 175 bar. Reheater . Steam from the exhaust of the first stage turbine goes back to the boiler for reheating and is returned to the second stage.

lexie@zozen.com > Get A Quote >

Difference Between Low- and High-Pressure Boilers | Hunk

A boiler is an appliance designed to heat water and produce energy. The heat is applied to water in an enclosed container before being distributed throughout the system. The major difference between a low-pressure and a high-pressure boiler is the amount of pressure per square inch and pounds per square inch gauge that the boiler produces.

lexie@zozen.com > Get A Quote >

Boiler Types and Classifications - Wiki - odesie by Tec

In typical packaged steam boiler operations, the boiler system may generate steam at about 150 psig for distribution throughout the facility and may be lowered to the operating pressure of equipment supplied through point-of-use pressure reducing stations.

lexie@zozen.com > Get A Quote >

Calculate How To - Department of Ener

process stream, outside the boiler island battery limits, with only some “top-up” heat recovery against hot boiler blowdown. The use of steam to preheat boiler feedwater was common when energy was cheap, but using surplus process heat instead (from below the “process pinch” temperature)

lexie@zozen.com > Get A Quote >

Plumbers Edge Tridicator/Boiler Temperature and Pressur

Plumbers Edge Tridicator/Boiler Temperature and Pressure Gauge application is for hot water and steam pressure for boilers. The PE401 makes it easy to monitor your boiler's internal temperature and pressure level. The sensing element for temperature is a bi-metallic coil and the pressure is measured by a …

lexie@zozen.com > Get A Quote >

How NOT to Design a Steam System - The C&S Compani

How NOT to Design a Steam System . Sizing a Steam Boiler Many Steam boilers are undersized for the actual NET load Determine the BTU required for the heat load Add losses for the piping, distribution, etc. Typical steam header design . Main Steam Header 19 Poor header examples:

lexie@zozen.com > Get A Quote >

4 things to look out for in steam boiler pressure control

9/28/2016 · The boiler operating control is set at the desired steam pressure of the boiler. On-off steam systems for comfort heating are usually set for an average of 2 lb. of steam pressure. The operating control is an automatic one that will cycle the boiler between the settings of the pressure control as long as there is a call for heat.

lexie@zozen.com > Get A Quote >